bonding strength

On-Line Examination Method of Bonding Strength Measurement in Silicon MEMS Devices

硅MEMS器件键合强度在线检测方法

A Study on Bonding Strength of Hybrid Integrated Circuits

功率混合集成电路键合强度控制研究

Some suggestions on construction are presented from the angle of bonding strength.

最后从新旧混凝土的粘接强度的角度讨论了后浇带的施工问题。

After HF acid etching under 5 different HF concentrations and 6 exposing times, shear bonding strength of porcelain to enamel were tested.

选择30个氢氟酸（HF酸）浓度－时间搭配点，测试瓷贴面复合体整体粘结抗剪强度。

The bonding strength and precision at high temperature satisfied the design requirement.

并在其外表面溅射镀铜,粘接强度及粘接精度在高温环境下均达到设计要求.

At the stoving temperature the reactions among the functional groups carboxy and hydroxy of binder makes line-type polymers into network polymers leading bonding strength.

在烘干8温度（220～250℃）下，粘结剂分子内羧基和羟基官能团之间继续发生反应，使线型聚合物变成网状体型聚合物，从而获得粘结强度。

Non-yellowing, strong initial bonding strength and heat-resistance.

不黄化型, 初期接着力佳,耐热性佳.

Influence of contact pressure to bonding strength between fiber sheets and concrete

接触压对纤维布与混凝土粘结强度的影响

The conclusion which the bonding strength is obviously influenced by the interlaced yarns.

得出空气变形丝对涂层织物的剥离强度具有显著影响的结论.

The bioceramic coating by laser cladding has high bonding strength and e.

介绍了在奥氏体不锈钢基材上激光涂覆生物陶瓷涂层的研究结果.

The captioned strength is forecasted in terms of different bonding points in a single concealed layer by means of BP calculating program.

应用BP算法程序对双金属材料的剥离强度按单隐蔽层不同结点数进行预报计算。

And the effect of some factors on bonding strength is also introdueed.

并阐明对胶粘剂粘着力产生影响的一些因素.

Study on the bonding strength of the adhesive with low viscosity for building

工艺参数对低粘度建筑结构胶粘接强度的影响

Research progress in the effect of different porcelain conditioning techniques on bonding strength

极限黏结力〔土地〕不同瓷表面处理方法对托槽与瓷面黏结性能影响的研究进展

Thermal Stability and Bonding Strength of Hydroxyapatite/ zirconia Composite Coatings

羟基磷灰石/氧化锆复合涂层热稳定性和结合强度的研究

Interface Bonding Strength of Composite White Cast Iron Embedded Steel Bar

加筋复合白口铸铁界面的结合强度

By adhesive bonding strength, combines two solid materials on the surface of the method call.

通过胶粘剂的粘结力, 将两种固体材料的表面连接起来的方法叫粘结.

The properties of fired paste and the viscosity strongly affect diffusion bonding strength.

浆料的烧成特性和粘度对扩散连接强度影响较大.

On the other hand , the adhesive shows properties with good bonding strength, resistance heating aging.

且粘接强度较高 、 耐介质 、 耐老化等综合性能优良.

It is considered traditionally thatadhesion agent's bonding strength is not enough "

传统认为是粘结强度不够的原因.

The effect of reaction phase on bonding strength was also discussed.

分析了反应相对接头强度的影响。

The result showed that the modified chitosan can improve fiber strength to some extent and can increase the bonding area.

对改性壳聚糖的增强机理进行初步研究表明：改性壳聚糖能够提高天津科技大学硕士学位论文纸张纤维本身强度，并且能够增加纤维间的结合面积。

Effect of ultrasonic power on the wire bonding strength

超声功率对引线键合强度的影响

The micro structures and the relations between bonding rate and bending and fracture strength were analyzed.

分析了弯曲强度、断裂挠度与焊合率之间的关系及接头的金相组织.

The relationship of bonding strength and temperature are investigated.

分析了键合强度与键合温度之间的关系。

The effects of reaction conditions on bonding strength are discussed in detail.

着重讨论了反应条件对胶粘剂粘接强度的影响.

The effects of starch content in adhesive on bonding strength and water resistance were examined.

考察了小麦淀粉添加量对脲醛树脂胶应用于松木胶接时的胶合强度和耐水性能的影响.

The parent metal density must high, in the bonding strength be friends with.

基材密度要高 、 内结合强度要好.

A New Model For Determining the Interface Bonding Strength in Layered Composite Materials

确定层状复合材料界面结合强度的新模型

At last, the approach of increasing bonding strength and decreasing shearing stress is presented.

最后, 给出提高新老混凝土界面粘结强度和降低粘结面剪应力的方法.